国产 | 久你欧洲野花视频欧洲1_中文字幕日韩欧美一区二区三区_99热这里有精品_久久精品中文字幕_鲁大师影院在线观看

Technical Support Current Location: Home  -  Service  -  Technical Support

1. Purpose
This regulation is used to guide the operator to operate and use hydraulic equipment correctly.

2. Scope Of Application
This regulation is suitable for guiding the safe operation and maintenance of the hydraulic press of our company.

3. Operating Procedures
3.1 Before moving, check the fastness of each fastener. There are obstacles in the running parts and sliding surfaces.
3.2 Connect the power supply and check whether the electrical grounding is reliable. Then move the start button to check whether the motor is turning correctly or not. Then the motor is officially started.
3.3 Check the buttons, the limit switch, the hydraulic valve, the photoelectric protection device and so on.
3.4 Make an empty stroke for 10 minutes before working. It is confirmed that the pressure of the hydraulic system is normal and the movement of the working beam is flexible, and the work can be started.
3.5 It is strictly forbidden to exceed the maximum working stroke of the movable crossbeam (i.e. the minimum distance between the movable beam and the lower limit to the working table), and design the die according to the requirement so as to avoid any mechanical accidents.
3.6 At work, the machine should be used in the range of maximum nominal force to ensure the safety of the operator and not to exceed the maximum eccentricity of the machine.
3.7 When the machine appears unreliable, noisy, vibrant or serious oil leakage, it should be shut down immediately to analyze the cause of the failure and try to exclude the use of fault.
3.8 After the start of each class, we should first use the point move button to move a few back and forth of the movable beam, so as to ensure the liquid filled tank full of oil. Then turn to normal stretching.
3.9 The work oil pump should be shut down first when the work is finished. The power supply is cut off, the equipment is cleaned and the inspection records are made.

4. Maintenance
4.1 Recommends the use of N46 to N68 anti-wear hydraulic oil. When the room temperature is below 10 degrees, it is recommended to use N32# hydraulic oil. The alternative oil can be No. 30, No. 22 turbine oil or No. 30, 20 machine oil.
4.2 Oil should be replaced once a year in general. The oil used for the first time of the new machine should be completely released after two months of filtration and then injected into the tank. Such as the discovery of oil emulsion, opacity or colloidal sticky phenomenon should be replaced with new oil immediately; mixed water or other impurities should be replaced with new oil immediately.
4.3 The temperature of the machine's oil temperature is less than 60 C, so the user needs to install the cooling water on its own. When the oil temperature is high, the water must be cooled to ensure the normal operation of the machine.
4.4 The oil pump oil filter oil filter should be removed and cleaned after the new machine is used for about 400 hours. Should every three months shall be washed once with kerosene or gasoline after. When the filter is removed, the machine should be shut down first. After dismantling, clean it with kerosene or gasoline, and then use it. If the oil filter is found to be serious or perforated, the new one should be replaced immediately. It is forbidden to open the machine without installing the oil filter.

Copyright ? 2017 All Right Reserved
综合国产综合亚洲综合| 虎白女粉嫩尤物福利视频| 无码永久成人免费视频| 亚洲精品久久久久一区二区| 色综合久久久久综合一本到桃花网 | 边做边流奶水的人妻| 国内成人在线激情视频| 香港aa三级久久三级| 十八禁无遮挡99精品国产| 96久热视频只有精品| 色偷偷亚洲第一成人综合网址| 色欲色香天天天综合无码www| 校园春色~综合网| 亚洲成av人片在www色猫咪| 伊人久在线观看视频| av免费网站在线免费观看| 国产露脸无套对白在线播放| 中日韩高清无专码区2021| 日韩av无码免费播放| 亚洲av成人无码一区无广告| 麻豆高清免费国产一区| 亚洲国产av无码精品无广告| 在线天堂中文www官网| 人妻被按摩师玩弄到潮喷| 亚洲男同志网站| 精品国产三级a∨在线| 午夜国产成人自拍视频| 动漫无遮挡羞视频在线观看| 亚洲中文字幕无码乱线| 久草精品手机视频在线观看| а中文在线天堂| 日韩精品射精管理在线观看| 久久久国产打桩机| 精品爆乳一区二区三区无码av| 男女啪动最猛动态图| 中文幕无线码中文字蜜桃| 亚洲国产综合精品一区| 亚洲一码二码三码精华液| 欧美极品少妇×xxxbbb| 婷婷久久综合九色综合88| 中文字幕人妻中文av不卡专区|